ANTIGUA TERRACOTTA

IMPORTANT!!!  READ CAREFULLY BEFORE INSTALLATION

Inspection & Storage

1. Upon receipt of your order, please inspect all tiles carefully.
2. Rock Mill will not be responsible for product issues once tiles have been installed.
3. Report any issues to Rock Mill within 30 days.
4. Exercise care when handling tiles during installation, to avoid chipping or scratching.
5. Keep tiles dry and store boxes in a dry area, away from dampness, to avoid damage.

Substrate & Membranes

1. Consult a licensed contractor for complete, proper installation and guidance.
2. Terracotta is made from natural clay. Expect variation in color, size, thickness & texture.
3. Mix tiles from different boxes throughout the install process and lay them out before setting them to determine the best look. Wipe any residue off tiles before installation.
4. Install surface should be clean, solid, level and without cracks. Walls should be plumb. Installation should not be started until the substrate meets these conditions.
5. For interior installations, use a waterproof membrane, such as Schluter-Ditra, which offers uncoupling (anti-fracture). For waterproofing, vapor management and reduction of efflorescence, use Schluter-Kerdi . Follow the manufacturer’s instructions.
6. For radiant heat, Schluter Ditra-Heat membrane offers heat, uncoupling (anti-fracture), waterproofing and vapor management. Follow the manufacturer’s instructions.
7. Rock Mill never recommends using terracotta tiles in shower pans, submerged applications or steam showers.

 Thin Set & Tile Setting

1. Always use a licensed installer to ensure quality installation.
2. For adhesive to set the tiles, use a high quality, unmodified thin-set adhesive, such as Laticrete. Follow the manufacturer’s instructions.
3. For optimal adhesion and to avoid moisture absorption through the tile, it is essential that each tile be back buttered and fully bedded for firm support.
4. Place tiles into wet mortar & adjust tile positioning as necessary for a level installation.
5. Wipe any excess thin set from the tiles immediately.
6. Allow tiles and substrate to dry completely without covering the area for at least 24 hours.

 Grouting

1. Use a grout bag to apply premium grout in between tiles. Avoid getting grout on surface.
2. DO NOT allow grout to dry on tile surface. Remove excess grout immediately with water and a sponge. Repeat the process until the surface is clean. Dry with a soft, clean cloth.

 Sealing

1. Use a high-quality sealer, such as Rock Shield Sealer, which is a no-VOC, penetrating sealer that will protect terracotta, cement, natural stone, grout, etc. from damage caused by water, salts, and oil-based stains.
2. If tiles are used in areas that may get wet, each tile should be “dip-sealed” before setting.
3. Treated surfaces are easier to clean and maintain longer.

Floor Protection

1. Protect the entire floor with thick paper or cardboard until any construction is finished.
2. Do not use any type of tape on tiles, as it will lift the stain and leave marks.

Maintenance & Repair
Surface may gradually lose patina over time, depending upon traffic and usage.

1. Clean floor surface with vacuum cleaner to pick up loose dirt. Use a clean mop or cloth with a PH-neutral, natural soap cleaner and water. Natural soap has cleaning and sealing properties, as the soap residue will fill open pores and add to the patina-look.
2. Do not use harsh cleaners such as bleach or detergent; this will not remove the sealer but will change the compound of the product.
3. When completely clean & dry, re-apply stain and/or Rock Shield Sealer as needed for higher traffic areas.
4. Terracotta is naturally porous. A moisture barrier and a high quality, penetrating sealer is recommended for resistance to staining and moisture absorption. Consult a licensed installer and follow recommended installation instructions.

Rock Mill Policies

1. Please inspect ALL material upon receipt. Claims will not be honored after installation.
2. Rock Mill considers the actions of the installer/contractor/3rd party whom the customer authorizes to pick up the material to be the responsibility of the customer.
3. Rock Mill will not honor claims made by the customer due to unauthorized or improper installation by the customer’s installer/contractor.
4. Please ensure that enough material is ordered to complete the job.
5. Add-on orders purchased later may vary. New batches are not guaranteed to match the original order, so it is always recommended to provide a control sample.
6. All items that are stocked are located at the Rock Mill Gardena, California warehouse.

Please inspect ALL material upon receipt. Claims will not be honored after installation. Rock Mill considers the actions of the installer/contractor/3rd party that customer authorizes to pick up the material to be the responsibility of the customer.

Rock Mill will not honor claims made by the customer, due to unauthorized or improper installation by customer’s installer/contractor. Please ensure that a sufficient quantity of stone is initially ordered to complete the job.

Add-on orders purchased later may vary slightly as new batches may come from different parts of the quarry and will not be guaranteed to match the original order.

All items that are stocked are located at the Rock Mill Gardena, California warehouse.

For more information, please contact your Rock Mill rep. Thank you!